3 Pin Plug to IEC C13

 

PRO-3PP-C13-2M-CC

Australian 3 Pin Plug to IEC Female C13 Curly Cord.

 

We now have three versions. All of these options have Very Strong Spring Force.

 

Part Number
PRO-3PP-C13-2M-CC
3 Pin Plug to IEC Female C13 Curly Cord
2m length (before coiling) Approx. 230mm coil, 100mm tails.
Extends to Approx. 1m Max
Qty  Unit Cost Ordering Link
1-9 $21.00 Click here to order
10-99 $16.50 Click here to order
100+ $13.50 Click here to order

 

Part Number
PRO-3PP-C13-3M-CC
3 Pin Plug to IEC Female C13 Curly Cord
3m length (before coiling) Approx. 3300mm coil, 150mm tails.
Extends to Approx. 1.5m Max
Qty  Unit Cost Ordering Link
1-9 $31.50 Click here to order
10-99 $24.75 Click here to order
100+ $20.25 Click here to order

 

Part Number
PRO-3PP-C13-5M-CC
3 Pin Plug to IEC Female C13 Curly Cord
5m length (before coiling) Approx. 630mm coil, 150mm tails.
Extends to Approx. 2.5m Max
Qty  Unit Cost Ordering Link
1-9 $52.50 Click here to order
10-99 $41.25 Click here to order
100+ $33.75 Click here to order

 

All +GST

We can also supply short little adapter cords, to convert the above cords into curly extension cords.

When ordered with one of the above cords the price is:

PRO-3PS-C14-AC 3 Pin Mains Socket, to IEC C14
Adapter Cord
$8.50

+GST

Click here to order

 

17 thoughts on “3 Pin Plug to IEC C13

  1. anthony says:

    I regularly supply a number of 3 Pin Plug to IEC Female C13 2m length unit except with a 90 degree IEC Female and a straight cable

    Approximately 50 – 100 are destroyed each quarter and if above is available may provide as a solution.

    Additionally I am after a curly cord to run from Vehicle to Hiab on Trailer running 12V from vehicle alternator to trailer mounted battery. Anderson plugs I presume would be ideal for this application but I was unable to locate anything on the site.

    Regards,

    Anthony

  2. Clint says:

    Hi ,
    I was wondering how much this lead was & if it was possible to get it without the C13 end? Also what size cable is it?
    I was hoping to use it to run from a power point (plugged in) to another power point (hard wired) mounted in the back of a bathroom vanity drawer.

    Regards,
    Clint.

  3. George says:

    Hi i was wondering if you had a 90 deg ( to the side) iec cable with a15cm tail, 1meter stretch is fine or anything close to that, any colour is fine too.

    • Paul Scott says:

      Hi George,
      Sorry these are the only ones we have at present.
      I might have some IEC Right angle leads, but only straight. (Not curly)

      Best regards
      Paul.

        • Paul Scott says:

          Hi Rupert,
          Sorry…No.
          The high temp kettle fittings have a slot in the top of the connector to prevent these normal IEC cords being used.
          We could probably get some made, but would likely need to do a run of a couple of hundred of them.

    • Sam geadah says:

      Hi I need2meters curly extensions cable lead ( exactly like the ordinary extension)
      Please advise

      • Paul Scott says:

        Hi Sam,
        Sorry…we don’t have any curly domestic extension leads with molded connectors.
        (As far as I know they don’t exist)
        Our mains curly cords are usually only used for commercial, and industrial applications.
        We can supply curly mains cords, but the ends need to be fitted by a licensed electrician.

  4. Greg McConnell says:

    Hi Paul … It’s been a couple of years since the question has been asked so here goes … Can you do the PRO-3PP-C13-2M-CC cable with an IEC right-angle entry plug? … and … what size conductors does it have? … I’m presuming it’s rated at 10 amps?
    Cheers, Greg

  5. Bruce Harding says:

    hi i am after a 3 core 10 240 volt curly cord 3 mts when stretched out , and also a 12 volt 4 core 5 amp curly cord 3 mts when stretched out can you supply these cables pls
    thanks Bruce

  6. Tony Manganiello says:

    Hi Paul, do you have these leads with a 90 degree IEC plug on one end,needs to be curly, thank you,
    Regards Tony.

Leave a Reply to Paul Scott Cancel reply

Your email address will not be published. Required fields are marked *